DIY Buffet Caddy from an Old Pallet

Sponsored by Ryobi Tools

Let me preface this post by saying – I am well aware of the pool set up by my family members and close friends on Facebook regarding my power tool use.  Everyone is taking bets on what appendage will be the first to go and the time frame in which is will happen.  Hate all you want, people, but be prepared for my awesomeness.  And this is only the beginning…

Now for the back story.  I picked up three pallets about a year and a half ago.  They have been sitting in my basement collecting dust because I was not strong enough to pry them apart and my husband refused to do it since it was my project.  I HAD to figure out a way to use these pallets so I could prove him wrong.  He was going to have me abandon them when we move later this month!  When I started on my Power Tools for Mommies series, I was able to dream up something to make from these babies.  {And say “I told you so”.}  I finally decided on making a DIY Buffet Caddy from that worn wood.  It’s perfect for cookouts and barbecues!

DIY Buffet Caddy from an Old Pallet - full tutorial at createcraftlove.com  #DIY #buffetcaddy #powertools #ryobination

Wanna make your own DIY Buffet Caddy?

Here’s what you need:

Old pallet {or you can use new wood and distress it yourself}

Ryobi 18V One+ Lithium Ion Starter Combo Kit – Circular saw and drill

Ryobi Air Strike and 1-1/4” 18 Gauge Brad Nails

Saw horses

Clamps

Wood glue

3/4 inch wood bit

P825_9_Final-1000x1000

I enlisted my dad’s help for this project since he’s an engineer and could help me figure out the little details of designing the plan.  Here’s what we came up with over coffee at IHOP the other day.

buffetcaddy2

Utensil dividers not pictured – blogger fail!

I wanted the utensil sections to be an inner dimension of 3 inches by 3 inches and there are three of these.  I wanted the area for the napkins to be equal to the size of the utensil sections.  That means the napkin area would be 3 inches by 9 inches.  Since the wood from the pallet is 1/2 inch deep, that would make my outer dimensions 11 inches by 7.5 inches {the three sections = 9 inches plus the 4 dividers which are 1/2 inch each}.  The wood is 5 inches wide.  I wanted it to be portable so we decided to do the middle divider in two sections {7 inches in height so we could cut out a handle hole}.  Are you keeping up?  This is why I enlisted the engineer…LOL

Armed with our plan of attack, we headed back to my house and inspected the pallets.  Turns out it was a good think I had three of those bad boys.  I used bits of wood from all three to get the straightest pieces.

buffetcaddypallet

These pallets were too strong to pry apart, so I just used the circular saw to cut off the pieces I needed – careful to avoid any nails.

Now it’s time to begin cutting your wood for the DIY Buffet Caddy!

Here’s what to cut:

Bottom = (2) 10 inch x 3.25 inch pieces

Back and front = (2) 11 inch x 5 inch pieces

Sides = (2) 6.5 inch x 5 inch pieces

Middle divider = (2) 7 inch x 5 inch pieces

Utensil dividers = (2) 3 inch x 5 inch

I used my Ryobi circular saw.  Not gonna lie, I was a little scared of losing an appendage.  The thought of having my dad there with me helped a lot.  What became evident is how slow I am at cutting with a circular saw!  HA!  I was afraid of a) losing aforementioned appendage or b) messing up the cut.  Turns out I still have all appendages but lots of scrap wood!  hee hee

buffetcaddysaw1

It also became clear that I needed a guide of some sort because I veer off towards the end of the cut.  Here’s a little trick my dad taught me…Clamp the wood to the saw horses.  Never cut between the saw horses!  Only on the end!  Then grab a squared piece of wood and clamp to the piece to be cut.  Be sure to measure the foot of your circular saw from the blade to the edge and add that to the measurement.  Otherwise, your pieces will be WAY off!

buffetcaddysaw2

Once everything is cut, you need to measure the middle divider for the handle.  We made the opening for the handle 3 inch by 3/4 inch.  Measure down 1 inch from the top of the piece.  Then measure down 1.75 inch from the top.  Using those markings, draw two parallel lines approximately an 1.5 inches long from the inner edge.  To mark the center of the hole for the drill bit, measure 1 3/8 inch from the inner edge and centered between the two lines.

Mark with an “x”.  This will be where you place the point of your wood bit.

buffetcaddywoodbitmark

Attach the 3/4 inch wood bit to the drill, clamp the wood to the saw horse and begin drilling.

buffetcaddydrill

When the tip of the wood bit pierces through the other side of the wood, stop drilling and turn wood over.

buffetcaddysmallhole

Restart drilling from this side, using the hole as your mark.  This will prevent the wood from splintering.

buffetcaddybighole

Now using the lines that you marked, cut out the rest of the handle using the circular saw.  GO SLOW!  You do not want to cut through the other side of the drilled hole.  You will have to turn the board over to finish the cuts because the curvature of the blade means the bottom side of the cut will not go as far as the top.

buffetcaddyhandlecut

Once the handle was cut, Dad and I discussed whether we should angle the corner of the middle divider.  We thought it would look nice to cut them.  We measure one inch down the side and two inches across the top.  Then drew a line connecting them with the square.  Use the circular saw to cut along the line.  Repeat on the other piece of the middle divider.

buffetcaddycorners

Let’s start assembling your DIY Buffet Caddy!

Frame out the sides.  Do this prior to gluing and nailing so you can make sure your pieces fit together nicely.

buffetcaddyunassembled

Once you are confident everything fits as it should, apply wood glue to the edges of the short sides.  Add some glue to the inner side of the long pieces where the sides connect.  Clamp together to allow for the wood glue to cure.

buffetcaddysideassembly

My sweet father bought me the Ryobi Air Strike!  I had a chance to try it out at SNAP!  It.is.amazing!  No air compressor required!  It can shoot up to 700 brads in a SINGLE charge!

P320_1v3_Final-1000x1000

I used it to nail the sides together.  Then unclamp and nail where the clamp was placed.

Next you will add the bottom panels.  Glue all around the edges that will be touching the sides.  Clamp in place and nail as you did with the sides.

Here’s the tricky part…the middle divider.

Mark three inches in from each side.  Draw a line using your square.  Apply wood glue to one edge of the utensil divider and apply to the inside of the line.  Repeat on the other side.  Clamp the dividers in place and nail.

buffetcaddyhandleassembly

Apply wood glue to the middle of the two large pieces where the handle is.  You will also need to apply wood glue to the edges that will come in contact with the sides.  Be sure on the edge of the middle divider to only glue up 5 inches {since the upper part is exposed}.

Insert into the side framed piece.  Measure your sections.  The inner diameter of the utensil sections is 3 inch x 3 inch.  The inner diameter of the napkin section is 3 inch x 9 inch.  Adjust the divider appropriately.  Clamp into place.  Nail the edges of the middle divider and the utensil dividers.  Remove the clamps and nail where the clamps were.

Re-apply clamps once assembled to ensure the wood glue cures in the center of the two middle dividers since we did not secure these with nails.  I also added a clamp to the top of the handle so it was centered.  Let dry overnight.

buffetcaddyassembled

I am in LOVE with how this turned out!  Something I built with my own two hands!  It was harder designing it than building it!

buffetcaddyempty

DIY Buffet Caddy from an Old Pallet - full tutorial at createcraftlove.com  #DIY #buffetcaddy #powertools #ryobination

DIY Buffet Caddy from an Old Pallet - full tutorial at createcraftlove.com  #DIY #buffetcaddy #powertools #ryobination

Are you loving the Power Tools for Mommies series?  I’m pretty sure I have cooler tools than my hubby now!  I am having a blast stepping out of my comfort zone and learning something new!  I hope you are too!  I linked this project up at Ryobi Nation!  Have you joined yet?

powertools

You could easily whip this DIY Buffet Caddy up for your Fourth of July or Canada Day celebrations!

Jill

 I was given free product from Ryobi Tools for the purpose of this post.  To read my full disclosure, click here.

Linking up to Home Stories A to Z

About Jill @ Create.Craft.Love.

Jill Fritz is a full time outside the home working mommy turned craft blogger. She offers craft/DIY tutorials for Pinterest addicts, craft junkies, DIY fanatics and busy mamas. Jill started Create.Craft.Love. as place to showcase her craftiness and to encourage others to do the same. Create.Craft.Love is a place where passion and creativity collide!
Google

Comments

  1. Oh yeah, Jill! I love it! I just asked for a compound miter saw for my birthday (next month). I’m on the power tools band wagon! I can’t wait to make one of these!!

    • Jill @ Create.Craft.Love. says:

      Thanks Chelsea!! I want a compound miter sooooo bad! Getting ready to build a farmhouse table!

  2. Crystal says:

    You did an awesome job!! You should be so proud of yourself!! Great job!!

  3. Looks awesome!! Go girl!

  4. This is so cute! And so very useful! I need one so bad. Thank you for sharing.

    I’d like to invite you to our Organize Me! Sizzlin’ Summer Link Up Party at Get Your Crap Together!

  5. I really love your caddy Jill! :-) but I love most about it is that you are able to use your own tools :-)

  6. Your buffet caddy looks great! Thanks for the tutorial!

    Ritchil
    http://chengand3kids.blogspot.com/

  7. What a great tutorial! Thank you so much for sharing :)

  8. Fabulous job… love your step by step tutorial!

  9. I love this tutorial! Especially since it uses pallet wood and a circular saw! GO YOU!

  10. You go with your power tools girl! Thanks for sharing you pallet post. I am grateful.

  11. I have a pile of pallets I have been dying to do something with! Thanks for the idea!

  12. This is a great idea! It’s perfect for parties and so cute!

Trackbacks

  1. [...] A DIY Buffet Caddy from Create Craft Love. [...]

Speak Your Mind

*

create craft love